Fluidd installation
1. What is a Fluidd?
Fluidd in lightweight alternative to Octoprint offering the same capabilities (if you forget that Octopint plugins have ever existed). It can also run on older and less powerful Raspberry versions.
I prefer it over the Octoprint due to the better user exprience and Klipper friendly options and settings.
Please note that this guide is for a new (clean) installation.
More about Fluidd can be found on official Fluidd website or a Discord channel.
1.1. Web interface
Short comparisom between desktop and mobile Fluidd web interface.
There are many other options, tabs and features in the Fluidd.
Desktop browser interface
Mobile browser interface
1.2. What comes with the FluiddPi package?
The whole FluiddPi package contains all you need:
Raspberry Pi OS Lite image
Fluidd
Klipper
Mooonraker
2. Hardware requirements
You will need:
Micro SD (SDHC) card with at least 8GB capacity
Micro SD card reader
5V power source (3A for Raspberry Pi 4)
USB cable (USB-C for Raspberry Pi 4, micro USB for older versions)
WiFi network or a standard LAN network + cable
I would also recommend:
Raspberry cover
Heatsinks
Fan for active cooling
The easiest way to get all parts is buying a complete set such as this one:
3. Download and install recommended programs
3.1. Download and install PuTTY
Install SSH client such as a PuTTY.
This client will be used to connect your PC to Raspberry.
Click here to download.
3.2. Download and install BalenaEtcher
We will use this program to flash FluiddPi OS image to micro SD card.
Click here to download.
3.3. Download and install Advanced IP Scanner
This program will be used for locating Rasperry in your local network.
It is not possible to connect to Raspberry via SSH without the correct IP address.
Click here to download.
4. Prepare Raspberry
4.1. Install heatsinks
Double check if you have everything you need.
I have used a Raspberry Pi 4, that requires heatsinks and active cooling is even a better option.
These three heatsinks are in the official distribution package. Remove the protective foil and apply then on the chips.
4.2. Install the case/cover
Install the Raspberry into the desired place / case / cover.
I have a designated place in my electronics compartment, so I will not use the original case.
5. Download and flash FluiddOS
5.1. Download OS image
Visit the official Fluidd Github release page and download the latest release.
Click here to download.
5.2. Flash from file
Take the Raspberry micro SD card, insert it into the card reader.
Open Balena Etcher and click on Flash from file.
5.3. Select the FluiddPi OS image
Select the downloaded image and hit Enter.
5.4. Select target
Click on Select target.
5.5. Choose the micro SD card
Select the correct target device, in this case the 32GB micro SD card.
Click on Continue
5.6. Flash Fluidpi image
Click on Flash! to flash the OS image on the micro SD card.
5.7. Flash confirmation
You have successfully flashed Fluidd OS image.
6. WiFi settings (optional)
6.1. Remove and insert the micro SD card into your computer
Micro SD card is automatically safely removed after tha flash.
Remove the micro SD card from the reader and insert it again.
6.2. Locate configuration file
Open the micro SD card in the file explorer and locate fluiddpi-wpa-supplicant.txt in the root directory.
6.3. Open configuration file
Open the file in a text editor such as a PSPad Editor or similar.
Locate WiFi settings.
6.4. Fill in your WiFi configuration
Find out what WiFi security type you use, the most common is a WPA/WPA2 secured.
Uncomment those 4 lines and enter your WiFi name and passsword inside “”.
6.5. Set your country code
Open this ISO3166 country list and fill in your country code.
For example: I live in the Czech Republic, so my country code is CZ.
Do not forget to save the file and safely remove the micro SD.
7. First boot
7.1. Power off
Make sure that the Raspberry is turned off – it does not have a power button, so simply remove or turn off the power source.
7.2. Insert micro SD card
Insert the flashed micro SD card into the Raspberry.
Make sure that the card holds in it’s place – the card reader has a lock position.
7.3. Insert LAN cable (optional)
If you are going to use a wired LAN connection, insert the cable.
I personally prefer WiFi, because I do not want to have cables everywhere.
7.4. Power on
Turn on the power source, LED diods in Raspberry will start flashing.
8. Installation verification
8.1. IP address localization
Start with locating Raspberry in your local network.
I highly recommend installing Advanced IP Scanner CLICK HERE.
Default IP range is usually 192.168.0.1-254 or 192.168.1.1-254.
Locate the Raspberry’s IP address and copy it.
You can simply copy the IP address or default local address: http://fluiddpi.local into the browser and open the Fluidd interface.
8.2. SSH connection (optional)
Open PuTTY and paste the copied IP address from previous step.
Click on Open.
8.3. Verification
You will see this window the first time you connect to the Raspberry from your computer.
Click on Yes.
8.4. Login
Use your Raspberry login, default is pi
Hit Enter.
Enter password for pi account.
Default value is raspberry
If you are not familiar with Linux systems, do not be scared that you will not see the password, not even * characters.
You should see these informations after a successful login
9. Next possible steps
You have succesfully installed Fluidd.
The next logical step would be to flash your board and create a printer configuration file.
9.1. KIAUH installation
10. FAQ
10.1. I cannot find the device in my local network
10.1.1. Invalid IP range
The most common problem is a different IP address range.
For example: you are not able to locate any device on this range: 192.168.1.1.-254
So open network settings – click on the network / more informations and find your computer’s IP address.
As you can see, this IP address in in a 192.168.0.1.-254 range.
Fill in the correct IP address range 192.168.0.1.-254 and click on Scan.
10.1.2. Invalid WiFi settings
It is possible that you have entered incorrect WiFi settings.
Turn of the Raspberry, remove micro SD card, insert it into the computer, return to 6.1. and double check your WiFi settings.
Ahoj, v příručce pro fluidd stojí:
“Vynucené přihlášení?
S forced_loginsnastavením na truea bez definovaných uživatelů – Moonraker se předvolí podle vašeho trusted_clients:nastavení.
S forced_loginsnastaveným na truea s definovaným jedním nebo více uživateli – moonraker bude ignorovat vaše trusted_clients:nastavení a bude vyžadovat autorizační údaje.”
Nikde ale nemohu najít jak přesně konkrétně nadefinovat uživatele pro přihlášení jménem a heslem.
Nevíš jak na to ?
Díky
Ahoj, tohle jsem bohuzel neresil.
Have to ask.. is there any way to get back to the octoprint web ui once fluidd is installed?
Hi, I would recommend to start over and make a clean installation.
What are your reasons to go back?
Missing plugins?